HydroWorld SX-6000 Swim Spa

SX-6000 separates the spa and swimming area into two environments. You will be able to unwind in the spa zone pre or post-workout and then splash into the swim zone to master your body.

Key Functions:
Heating system
Radio & CD Input
Illumination system
Massage Therapy system
Ozone Sterilization
Filtration system
Balboa Spa Control

Key Specifications:
Seating capacity: 8-9 persons
Water capacity: 2558.51 gallons / 9685 liters
Shell color: Silver with white marble #6427 (standard)
Metal frame
Aristech Acrylic Colors
Spa Pack: GL-300 Spa Control with 3kw heaters x 2 sets
Filter & Cartridge (50 sq. ft) x 2 ea
Ozone Generator x 2
PS Gray Skirting
Pillows / Head & Neck Rests x 5
5" Swim Spa Jets x 6 ea
4" Power Flo Stainless Steel Spa Jets x 1 ea
3.5" Power Stainless Steel Spa Jets x 11 ea
2.5" Power Stainless Steel Jets x 12 ea
Jet Zone Diverters x 2 ea
Air Regulators x 6 ea
On/Off Valves x 2 ea
200 GMP Stainless Steel Suction x 8 ea
94 GMP Suction x 2 ea
2" Ball Valves x 8 ea
1.5" Ball Valves x 4 ea
1" Drain x 2 ea
5" Drain Valves x 2 ea
1" Drain Valve x 4 ea
1" Stainless Steel Air Jets x 15 ea
1" Stainless Steel Jets x 35 ea
5" Spa Master LED Lights x 4 ea
700 Watt Air Blower
Massage Pump for Swim Side (1 speed, 3hp) x 2 ea
Massage Pump for Spa Side (1 speed, 3hp) x 2 ea
24 Hour Circulation Pump: 1 x 0.5hp & 1 x 0.75hp
Rated Voltage: AC230V-240V, 50Hz

Shipping Dimensions: L x W x H
5850mm x 2210 mm x 1550 mm

Product Weight: 2794 lbs.

Shipping Weight: 2816 lbs.

Warranty
Structure: 5 years
Shell Finish: 2 years
Equipment & Controls: 1 year
Plumbing & Components: 1 year

*Note*
It's important that you contact a licensed electrician or contractor when planning for your hot tub electrical hook up. You should consult the owner's manual (included) for your specific model and provide the information to your electrician. Proper planning will ensure a safe hot tub installation that meets the local code and also help prevent any future financial setbacks.

If your hot tub runs on 240 volts, it must be permanently connected (hard wired) to the power supply.
If your hot tub runs on 120 volts, it may use a G.F.C.I. cord, plugged in to a dedicated grounded outlet.
The power supplied must be a dedicated circuit with no other appliances or lights sharing the power.
Wire size must be appropriate per NEC and/or local codes. It is determined by length of the run from the breaker box to the hot tub and the maximum current draw.
Copper wire with THHN insulation is recommended. Do not use aluminum wire.
The electrical supply for the hot tub must include a suitably rated switch or circuit breaker with a disconnection readily accessible to the hot tub's occupant, but installed at least five feet from the water. Check with local municipalities for additional code requirements.
The electrical circuit must include a suitable ground fault circuit interrupter (GFCI) as required by NEC.

Important!
When installed in the United States, the hot tub electrical requirements must meet the requirements of the National Electric Code (NEC) and any applicable state or local codes. The electrical circuit should be installed by a licensed contractor and approved by a local building/electrical inspector.